Cisco Router Basic Commands video tutoial – Configure FastEthernet interface

Posted on July 8, 2009. Filed under: CCNA | Tags: , , , |


In the section one of CCNA lab video tutorial 3, we will configure Router2 and Router0 for the FastEthernet interfaces. We will set the ip address of FastEthernet interface 0/0 of Router2 as 10.0.0.1 with subnet mask 255.0.0.0, then turn on the interface with command “no shutdown”. We do the same on Router0, set the ip address of FastEthernet interface 0/0 as 10.0.0.2 with subnet mask 255.0.0.0, then turn it on. We finally ping the ip address 10.0.0.1 on Router0 in order to verify Routers’ configuration.

IOS commands for Router 2

— System Configuration Dialog —

Continue with configuration dialog? [yes/no]: n
Press RETURN to get started!

Router>enable
Router#config t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#interface fa 0/0
Router(config-if)#ip address 10.0.0.1 255.0.0.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Router#show ip interface brief
Interface              IP-Address      OK? Method Status                Protocol

FastEthernet0/0        10.0.0.1        YES manual up                    down

FastEthernet0/1        unassigned      YES manual administratively down down
Router#

IOS commands for Router 0

— System Configuration Dialog —

Continue with configuration dialog? [yes/no]: n
Press RETURN to get started!

Router>enable
Router#config t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#interface fa 0/0
Router(config-if)#ip address 10.0.0.2 255.0.0.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Router#show ip interface brief
Interface              IP-Address      OK? Method Status                Protocol

FastEthernet0/0        10.0.0.2        YES manual up                    up

FastEthernet0/1        unassigned      YES manual administratively down down

Serial0/0              unassigned      YES manual administratively down down

Serial0/1              unassigned      YES manual administratively down down
Router#ping 10.0.0.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 31/31/32 ms

Router#ping 10.0.0.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 31/31/32 ms

Router#

Advertisements

Make a Comment

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

One Response to “Cisco Router Basic Commands video tutoial – Configure FastEthernet interface”

RSS Feed for IT Certifications Comments RSS Feed


Where's The Comment Form?

Liked it here?
Why not try sites on the blogroll...

%d bloggers like this: