CCNA Lab Video Tutorial 4 – Ref3 – OSPF Routing Command

Posted on July 9, 2009. Filed under: CCNA | Tags: , , , |


RouterA(config)#no router eigrp 111
RouterA(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
RouterA#show ip route
Codes: C – connected, S – static, I – IGRP, R – RIP, M – mobile, B – BGP
D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area
N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2
E1 – OSPF external type 1, E2 – OSPF external type 2, E – EGP
i – IS-IS, L1 – IS-IS level-1, L2 – IS-IS level-2, ia – IS-IS inter area
* – candidate default, U – per-user static route, o – ODR
P – periodic downloaded static route
Gateway of last resort is not set
C    10.0.0.0/8 is directly connected, FastEthernet0/0
C    20.0.0.0/8 is directly connected, Serial0/0
RouterA#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
RouterA(config)#ip router ospf 123
^
% Invalid input detected at ‘^’ marker.
 
RouterA(config)#router ospf 123
RouterA(config-router)#network 10.0.0.0 0.255.255.255 area 0
RouterA(config-router)#network 20.0.0.0 0.255.255.255 area 0
RouterA(config-router)#
01:07:30: %OSPF-5-ADJCHG: Process 123, Nbr 30.0.0.1 on Serial0/0 from LOADING to FULL, Loading Done
RouterA(config-router)#exit
RouterA(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
RouterA#show ip route
Codes: C – connected, S – static, I – IGRP, R – RIP, M – mobile, B – BGP
D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area
N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2
E1 – OSPF external type 1, E2 – OSPF external type 2, E – EGP
i – IS-IS, L1 – IS-IS level-1, L2 – IS-IS level-2, ia – IS-IS inter area
* – candidate default, U – per-user static route, o – ODR
P – periodic downloaded static route
Gateway of last resort is not set
C    10.0.0.0/8 is directly connected, FastEthernet0/0
C    20.0.0.0/8 is directly connected, Serial0/0
O    30.0.0.0/8 [110/65] via 20.0.0.2, 00:00:48, Serial0/0
RouterA#ping 30.0.0.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 30.0.0.10, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 62/62/63 ms
RouterA#

Back to CCNA Lab Video Tutorial 4

OSPF Routing Command for Router A

RouterA(config)#no router eigrp 111

RouterA(config)#exit

%SYS-5-CONFIG_I: Configured from console by console

RouterA#show ip route

Codes: C – connected, S – static, I – IGRP, R – RIP, M – mobile, B – BGP

D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area

N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2

E1 – OSPF external type 1, E2 – OSPF external type 2, E – EGP

i – IS-IS, L1 – IS-IS level-1, L2 – IS-IS level-2, ia – IS-IS inter area

* – candidate default, U – per-user static route, o – ODR

P – periodic downloaded static route

Gateway of last resort is not set

C    10.0.0.0/8 is directly connected, FastEthernet0/0

C    20.0.0.0/8 is directly connected, Serial0/0

RouterA#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

RouterA(config)#router ospf 123

RouterA(config-router)#network 10.0.0.0 0.255.255.255 area 0

RouterA(config-router)#network 20.0.0.0 0.255.255.255 area 0

RouterA(config-router)#

01:07:30: %OSPF-5-ADJCHG: Process 123, Nbr 30.0.0.1 on Serial0/0 from LOADING to FULL, Loading Done

RouterA(config-router)#exit

RouterA(config)#exit

%SYS-5-CONFIG_I: Configured from console by console

RouterA#show ip route

Codes: C – connected, S – static, I – IGRP, R – RIP, M – mobile, B – BGP

D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area

N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2

E1 – OSPF external type 1, E2 – OSPF external type 2, E – EGP

i – IS-IS, L1 – IS-IS level-1, L2 – IS-IS level-2, ia – IS-IS inter area

* – candidate default, U – per-user static route, o – ODR

P – periodic downloaded static route

Gateway of last resort is not set

C    10.0.0.0/8 is directly connected, FastEthernet0/0

C    20.0.0.0/8 is directly connected, Serial0/0

O    30.0.0.0/8 [110/65] via 20.0.0.2, 00:00:48, Serial0/0

RouterA#ping 30.0.0.10

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 30.0.0.10, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 62/62/63 ms

RouterA#

OSPF Routing Command for Router B

RouterB#show ip route

Codes: C – connected, S – static, I – IGRP, R – RIP, M – mobile, B – BGP

D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area

N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2

E1 – OSPF external type 1, E2 – OSPF external type 2, E – EGP

i – IS-IS, L1 – IS-IS level-1, L2 – IS-IS level-2, ia – IS-IS inter area

* – candidate default, U – per-user static route, o – ODR

P – periodic downloaded static route

Gateway of last resort is not set

C    20.0.0.0/8 is directly connected, Serial0/0

C    30.0.0.0/8 is directly connected, FastEthernet0/0

RouterB#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

RouterB(config)#router ospf 123

RouterB(config-router)#network 20.0.0.0 0.255.255.255 area 0

RouterB(config-router)#network 30.0.0.0 0.255.255.255 area 0

01:07:23: %OSPF-5-ADJCHG: Process 123, Nbr 20.0.0.1 on Serial0/0 from LOADING to FULL, Loading Done

RouterB(config-router)#exit

RouterB(config)#exit

%SYS-5-CONFIG_I: Configured from console by console

RouterB#show ip route

Codes: C – connected, S – static, I – IGRP, R – RIP, M – mobile, B – BGP

D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area

N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2

E1 – OSPF external type 1, E2 – OSPF external type 2, E – EGP

i – IS-IS, L1 – IS-IS level-1, L2 – IS-IS level-2, ia – IS-IS inter area

* – candidate default, U – per-user static route, o – ODR

P – periodic downloaded static route

Gateway of last resort is not set

O    10.0.0.0/8 [110/65] via 20.0.0.1, 00:00:35, Serial0/0

C    20.0.0.0/8 is directly connected, Serial0/0

C    30.0.0.0/8 is directly connected, FastEthernet0/0

RouterB#ping 10.0.0.10

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.0.0.10, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 49/59/63 ms

RouterB#

 

Advertisements

Make a Comment

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

2 Responses to “CCNA Lab Video Tutorial 4 – Ref3 – OSPF Routing Command”

RSS Feed for IT Certifications Comments RSS Feed


Where's The Comment Form?

Liked it here?
Why not try sites on the blogroll...

%d bloggers like this: